Sunday, March 4, 2012

Coal Bed Methane Product Water

The quantity of the CBM product water: 
Extraction of CBM involves pumping large volumes of water from the saturated coal seam in order to release the water pressure holding the gas in the coal seam. What to do with this volume of often marginal-quality CBM product water is a source of much debate. Each well produces 5 to 20 gallons of water per minute. At 12 gallons per minute, one well produces a total of 17,280 gallons of water per day. It is common to have to have one well every 80 acres, and in the Powder River Basin, there are up to three methane-bearing coal seams. Therefore, there may be up to three wells per 80 acres.

The quality of CBM product water and its effects on soil:  CBM product water has a moderately high salinity hazard and often a very high sodium hazard based on standards used for irrigation suitability. Irrigation with water of CBM product water quality on range or crop lands should be done with great care and managed closely. With time, salts from the product water can accumulate in the root zone to concentrations which will affect plant growth. Saline conditions stunt plant growth because plants must work harder to extract water from the soil.
The sodium hazard of CBM product water poses additional threats to certain soil resources. Sodic irrigation water causes soil crusting and impairs soil hydraulic conductivity, adversely affecting water availability and aeration and subsequent crop growth and yield. Upon wetting of soils containing swelling clay, sodium causes the degree of swelling in the clay to increase, leading to dispersion and migration of clay particles. Current research at Montana State University shows that water with sodium levels equal to typical Montana CBM product water can degrade the physical and chemical properties of heavier, clay soils, making such soils completely unsuitable for plant growth.
The risk of sodium degradation has been observed in other soil textures. Jim Oster (personal com.) observed crusting, poor soil tilth, hardsetting and aggregate failure on a sandy loam soil irrigated with water with EC ~ 1 and SAR ~ 7. Minhaus (1994) saw irreversible and severe reduction in infiltration on sandy loam soil with long term irrigation under high SAR water followed by monsoon rain. 
There are many factors in addition to soil textures that affect infiltration rates. Mineralogy, lime, sesquiozides, organic matter content, cultivation, irrigation method, wetting rate, antecedent water content and time since cultivation all play a roll in infiltration. The only way to be certain of the impacts of saline/sodic irrigation water on the soil is to periodically sample and test the irrigation water and the soil.

Coal Bed Methane (CBM) and CBM Product Water (ex. in Powder River Basin

What is coal bed methane? 
The primary energy source of natural gas is a substance called methane (CH4). Coal bed methane (CBM) is simply methane found in coal seams. It is produced by non-traditional means, and therefore, while it is sold and used the same as traditional natural gas, its production is very different. CBM is generated either from a biological process as a result of microbial action or from a thermal process as a result of increasing heat with depth of the coal. Often a coal seam is saturated with water, with methane is held in the coal by water pressure. Currently, natural gas from coal beds accounts for approximately 7% of total natural gas production in the United States.

How do people estimate the amount of methane gas which will come from a region underlain by coal?  There are two popular methods of estimating recoverable methane gas from a coal seam.
a. One method requires estimating methane reserves by boring to the top of the coal seam, then extracting a core from the coal. The amount of methane recovered from the coal core is used to estimate gas content per unit volume of coal. If a number of cores are drilled and methane gas release is observed, one can estimate the amount of gas available in a region. The limitations to this method are:
1) there is much disturbance to the coal seam core before gas release is measured;
2) it is expensive
3) not every region of potential CBM development has been drilled and explored
b. Another method of estimation is through a series of calculations based on information already known about the coal in the region and the feasibility of CBM development. For instance, the Montana Bureau of Mines and Geology estimated the amount of recoverable CBM in the Powder River Basin using the following information:
•  A coal seam has favorable reserves if it produces 50-70 ft3 per ton of coal. 
•  CBM extraction is economical at 50 ft3 per ton of coal when a coal seam is 20 feet thick or more. 
•  Coal bed methane exists only in areas where the dominant chemistry of the water in the coal seam is sodium bicarbonate and where the coal seam is buried deeply enough to maintain sufficient water pressure to hold the gas in place. 
The Environmental Impact Statement for CBM development in the Powder River Basin estimated the amount of coal in the region based on the total reported tonnage of coal in the region multiplied by 50 ft3 of methane per ton of coal, irregardless of seam thickness, depth or proximity to outcrop. 

How do gas companies extract methane from a coal seam? 
Since CBM travels with ground water in coal seams, extraction of CBM involves pumping available water from the seam in order to reduce the water pressure that holds gas in the seam. CBM has very low solubility in water and readily separates as pressure decreases, allowing it to be piped out of the well separately from the water. Water moving from the coal seam to the well bore encourages gas migration toward the well.
CBM producers try not to dewater the coal seam, but rather seek to decrease the water pressure (or head of water) in the coal seam to just above the top of the seam. However, sometimes the water level drops into the coal seam. 


Are coal seams aquifers? 
Yes. Water flows through fractures (or cleats) in the coal seam and if the cleat system is well developed and has enough water to pump and produce an economically viable and feasible water supply, the seam can be an aquifer. Coal seams are the most regionally continuous geologic unit in the Powder River Basin and have aquifer characteristics equal to or better than sandstones, so are frequently targeted for water-well completions.

Saturday, March 3, 2012

Spiral Wound Heat Exchangers

These heat exchangers have a broad temperature and pressure range and are used in single phase and two phase applications. They are able to handle many streams depending on the customers need. Pressures of up to 3625 psi can be handled sufficiently. The materials of construction of this exchanger include austenitic steels, aluminum alloys, carbon steel, nickel and chrome/moly alloys. This wide range of materials and the special features associated with the geometry of the heat exchanger allow for a wide range of applications. 
The surface area of heat transfer can be as high as 20,000 m2 but the maximum diameter is limited to 7,500 mm and a weight of approximately 260 tons per unit. It is possible to have larger diameters or higher weights but their feasibility has to be checked depending on the customer’s needs. 
The material of construction chosen depends on the customer’s needs. Simulations are The exchanger consists of a center hollow tube with tube bundles that spiral round it. The center tube and the tube bundle are housed in a metal column. The outer column does not have a uniform diameter. The bottom part has a larger diameter than the top part. Figures A and B show the outer shell and the tube bundles respectively. used for strength calculations of pressure containing vessels. Features such as tube spacing, tube support, bundle support and flexible mandrel are selected based on proven design technology developed over many years. 
Source:
Evaluation of LNG Technologies (by Valerie Rivera, Ayema Aduku, Oluwaseun Harris)
April 30, 2008 

Plate Fin Heat Exchangers

These heat exchangers are widely used in cryogenic application because of their low cost, small size, low weight, high thermal capacity and effectiveness relative to other types of heat exchangers. The result of the improved effectiveness is the achievement of true counter current flow where there is an increase in the temperature spread and a closer approach to ideality. This means that the refrigerant cooling curve is closer to the natural gas cooling curve. 
The exchanger is made up of manifolds or headers which consist of elements. A manifold and an element are shown below, Figures 4 and 5 respectively. An element is made up of a corrugated die-formed fin plate placed between flat metal separator plates. There are side bars along the outside of the fin sections. A stack of the elements is welded to form a rigid matrix and can be designed to meet any configuration and size. The stacks are welded onto the manifolds. Depending on the application, a number of manifolds can be assembled to form the heat exchanger.
Manifold or Header (xchanger.com)
An element
The wavy configuration of the fin promotes turbulence and therefore improves heat transfer. This increase in heat transfer is accompanied by an increase in pressure drop. This is a problem with low density fluids like gases because of the extra work required to surmount the pressure drop. 
Fin Configurations
This work is often much higher than the increase in heat transfer acquired from the fins. For applications where it is proposed any fin configuration other than the simplest, a thorough analysis of the effect on the system should be conducted.  
In designing the plate fin heat exchanger, it is possible to have different heights of the alternating fin plates. There is no requirement to have the same height or spacing of separator plates. This is a useful freedom to have in situations where the difference in density of the hot and cold fluids is large. In cryogenic systems, the refrigerant stream entering the expander has a higher density than the stream coming out of the expander. In such a case as this, it is necessary to use a larger height for the lower density stream so that a common Reynolds number and therefore heat transfer coefficient, U, can be attained.
Aluminum is the usual material of construction of plate fin heat exchangers for cryogenic applications. (Walker, 104-110)

Source:
Evaluation of LNG Technologies (by Valerie Rivera, Ayema Aduku, Oluwaseun Harris)
April 30, 2008 

Sunday, February 5, 2012

Why Become a Chemcal Engineer??!!!

 1. What is chemical engineering?

Chemical engineering is all about change - chemical and biochemical engineers create and develop processes to make useful products from raw materials, in a cost effective and safe manner.

2. What does the work involve?

Chemical engineers are trained to apply fundamental engineering principles, maximise economic returns and reduce environmental impact. Chemical engineers need to work as part of a team and develop good communication skills. Strong problem solving and analytical skills are also a bonus.

World’s Best Chemical Engineering Universities

USA and Canada

  1. Massachusetts Institute of Technology
    MIT is located in Boston, USA. MIT graduates and faculty are noted for their technical acumen (72 affiliated Nobel Laureates, 47 National Medal of Science recipients, and 29 MacArthur Fellows) and entrepreneurial spirit. The Department of Chemical Engineering at MIT have the largest chemical engineering faculty in the United States covering chemical engineering broadly, and in great depth. You may find further information about Che MIT here. For undergraduates, they have B.Sc degree in Chemical Engineering dan Chemical-Biological Engineering. For graduate school, they have M.S. CEP degree (Master of Science in Chemical Engineering Practice), Ph.D. CEP, and also Ph.D.
  2. University of California – Berkeley
    UC Berkeley is located in Berkeley, a city on the east shore of San Francisco Bay in Northern California, in the United States. By the 1930s, Berkeley had established itself as a premier research university, and today counts sixty-one Nobel Laureates among its faculty, researchers and alumni.The College of Chemistry offers undergraduate degrees in chemistry, chemical biology, and chemical engineering, as well as double majors in chemical engineering and materials science and engineering, and in chemical engineering and nuclear engineering. A new option is a concentration in materials chemistry. The college offers doctoral programs in chemistry and chemical engineering, and a master’s program in chemical engineering, including a concentration in product development. You may find further information about chemical engineering at UC Berkeley here.
  3. University of Toronto
    The University of Toronto (U of T) is a public research university in the city of Toronto, Ontario, Canada. The university is consistently placed among the leading academic institutions of the world. Newsweek magazine places the university first in Canada, and 18th worldwide, 9th among public universities, and among the top 5 universities outside the United States. The University is also affiliated with 9 Nobel laureates (6 alumni), the most of any Canadian university. Chemical Engineering and Applied Chemistry at the University of Toronto is one of the oldest and largest departments of its kind in North America. It has a rich history dating back to John Dalton of Dalton’s Atomic Theory and a modern reputation based on its state-of-the-art research achievements. You may find more information about chemical engineering at University of Toronto here

Saturday, February 4, 2012

Polietilen

Ada berbagai macam polietilen berdasarkan beda massa jenis dan banyaknya cabang. Berbagai macam polietilen yaitu:
1.      Ultra high molecular weight polyethylene (UHMWPE)
2.      Ultra low molecular weight polyethylene (ULMWPE or PE-WAX)
3.      High molecular weight polyethylene (HMWPE)
4.      High density polyethylene (HDPE)
5.      High density cross-linked polyethylene (HDXLPE)
6.      Cross-linked polyethylene (PEX or XLPE)
7.      Medium density polyethylene (MDPE)
8.      Linear low density polyethylene (LLDPE)
9.      Low density polyethylene (LDPE)
10.  Very low density polyethylene (VLDPE)
Polietilen yang terpenting adalah HDPE, LDPE, dan LLDPE.